Daktronics

How do I configure the 9/10s or tails options on the FL-3000/4500 Gas Price Displays using the DM-100 handheld?

Topic

  • How can I remove the 10 from the 9/10s?
  • How do I add or remove a tail from the 9 and 6 digit?

Environment

  • Product: FL-3000, FL-4500
  • Component: Gas Price or Petroleum Price Display, FL digit product
  • Control System: DM-100 handheld (FLD3-2000, FLR3-1500 kits)

Steps

Note: The menus have change slightly between the different revisions of the DM-100.  Below will have direction for the different menus.

  • DM-100 - DD-2256160 (3.0 or higher).  (This is displayed on the boot up of the handheld)
    1. Press Menu.
    2. Using the arrow buttons, scroll to Display Menu and press Enter.
    3. Using the arrow buttons, scroll down to Configuration and press Enter.
    4. Using the arrow buttons, scroll down to Configuration Style and press Enter.
    5. Select Network 1.  (For multiple networks(client radios) you will need to repeat this step for each network.)
    6. Select tails or no tails along with being able to adjust the 9/10s to show or not show the 10. The left figure is with DM-100 in Gas Price mode, the right figure is with DM-100 in Rate Mode.
      tails tenths configuration picture.pngInternational tails no tails.png
    7. Once you have used the arrow keys to select the option that is preferred, press Enter.
    8. After pressing enter, verify the display now shows the correct style, then press Menu to exit back to screen.
    9. If multiple radios repeat for each radio network step 5.
  
  • DM-100 - DD-2256160 (2.2 or lower).  (This is displayed on the boot up of the handheld)
    1. Press Menu.
    2. Using the arrow buttons, scroll down to Configuration and press Enter.
    3. Press the down arrow button once to get to Style and press Enter.
    4. Select tails or no tails along with being able to adjust the 9/10s to show or not show the 10.  See the following picture for the available options:
      tails tenths configuration picture.pngInternational tails no tails.png
    5. Once you have used the arrow keys to select the option that is preferred, press Enter.
 
 
Refer to the correct manual for more information.

KB ID: DD2839105

DISCLAIMER: Use of this content may void the equipment warranty, please read the disclaimer prior to performing any service of the equipment.

DAKTRONICS DOES NOT PROMISE THAT THE CONTENT PROVIDED HEREIN IS ERROR-FREE OR THAT ANY DEFECTS WILL BE CORRECTED, OR THAT YOUR USE OF THE CONTENT WILL PROVIDE SPECIFIC RESULTS. THE CONTENT IS DELIVERED ON AN "AS-IS" AND "AS-AVAILABLE" BASIS. ALL INFORMATION PROVIDED IN THIS ARTICLE IS SUBJECT TO CHANGE WITHOUT NOTICE. DAKTRONICS DISCLAIMS ALL WARRANTIES, EXPRESS OR IMPLIED, INCLUDING ANY WARRANTIES OF ACCURACY, NON-INFRINGEMENT, MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE. DAKTRONICS DISCLAIMS ANY AND ALL LIABILITY FOR THE ACTS, OMISSIONS AND CONDUCT OF YOU OR ANY THIRD PARTIES IN CONNECTION WITH OR RELATED TO YOUR USE OF THE CONTENT. ADJUSTMENT, REPAIR, OR SERVICE OF THE EQUIPMENT BY ANYONE OTHER THAN DAKTRONICS OR ITS AUTHORIZED REPAIR AGENTS MAY VOID THE EQUIPMENT WARRANTY. YOU ASSUME TOTAL RESPONSIBILITY FOR YOUR USE OF THE CONTENT AND ANY LINKED CONTENT. YOUR SOLE REMEDY AGAINST DAKTRONICS FOR DISSATISFACTION WITH THE CONTENT IS TO STOP USING THE CONTENT. THIS LIMITATION OF RELIEF IS A PART OF THE BARGAIN BETWEEN THE PARTIES.

The above disclaimer applies to any property damage, equipment failure, liability, infringement, or personal injury claim arising out of or in any way related to your use or application of the content, whether such claim is for breach of contract, tort, negligence or any other cause of action.