Daktronics

How do I log into the web interface for a DMP or VIP?

Topic

  • How do I log into the web interface for a DMP or VIP?

Environment

  • Product: 
  • Components: DMP-4060, DMP-8000, VIP-4060, VIP-5060
  • Control System: 

Steps

🔽 Use the arrows to open or collapse each section.

HTML interface

 Open a browser window and enter the device IP address and port (if not using port 80) in the address bar followed by pressing the Enter key, e.g. http://172.16.192.25 or http://172.16.192.25:81.

    • If using Internet Explorer, version 11 will be needed.
    • If connecting to a DMP-8000 you will be taken to its dashboard and be required to enter a password when saving changes. 
    • If connecting to a VIP-5060 you will be prompted for the username and password, enter them and click OK or Sign in.
Silverlight (legacy) interface
  1. Open a browser window and enter the device IP address and port (if not using port 80) in the address bar followed by pressing the Enter key, e.g. http://172.16.192.25 or http://172.16.192.25:81.
    • Note:  Depending on the display type and setup, the web port could also be on 82, 85, or 86.
    • You will receive several Java prompts to click past which may include the following:
      • "Your Java version is out of date."  Do not update Java, click Later on this prompt.
      • "Do you want to run this application? - CalibrationApplet"  Click the "I accept the risk and want to run this app." box to put a checkmark in it and click the Run button.
      • "Do you want to run this application? - ftpApplet"  Click the "I accept the rist and want to run this application." box to put a checkmark in it and click the Run button.
      • "Block potentially unsafe components from being run?"  Click the Don't Block button.
    • If connecting to a DMP-4060 or a VIP-4060 you will need Java version 6 or 7 as well as Microsoft Silverlight, it is recommended to use Internet Explorer for these.
    • If the device IP is not known, it may be captured by viewing the boot sequence on the display after power cycling or detected using Display Finder.
  2. The log in page for the web interface will open, enter the password (if one is being used) and click OK or Log In.

KB ID: 000002986

DISCLAIMER: Use of this content may void the equipment warranty, please read the disclaimer prior to performing any service of the equipment.

DAKTRONICS DOES NOT PROMISE THAT THE CONTENT PROVIDED HEREIN IS ERROR-FREE OR THAT ANY DEFECTS WILL BE CORRECTED, OR THAT YOUR USE OF THE CONTENT WILL PROVIDE SPECIFIC RESULTS. THE CONTENT IS DELIVERED ON AN "AS-IS" AND "AS-AVAILABLE" BASIS. ALL INFORMATION PROVIDED IN THIS ARTICLE IS SUBJECT TO CHANGE WITHOUT NOTICE. DAKTRONICS DISCLAIMS ALL WARRANTIES, EXPRESS OR IMPLIED, INCLUDING ANY WARRANTIES OF ACCURACY, NON-INFRINGEMENT, MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE. DAKTRONICS DISCLAIMS ANY AND ALL LIABILITY FOR THE ACTS, OMISSIONS AND CONDUCT OF YOU OR ANY THIRD PARTIES IN CONNECTION WITH OR RELATED TO YOUR USE OF THE CONTENT. ADJUSTMENT, REPAIR, OR SERVICE OF THE EQUIPMENT BY ANYONE OTHER THAN DAKTRONICS OR ITS AUTHORIZED REPAIR AGENTS MAY VOID THE EQUIPMENT WARRANTY. YOU ASSUME TOTAL RESPONSIBILITY FOR YOUR USE OF THE CONTENT AND ANY LINKED CONTENT. YOUR SOLE REMEDY AGAINST DAKTRONICS FOR DISSATISFACTION WITH THE CONTENT IS TO STOP USING THE CONTENT. THIS LIMITATION OF RELIEF IS A PART OF THE BARGAIN BETWEEN THE PARTIES.

The above disclaimer applies to any property damage, equipment failure, liability, infringement, or personal injury claim arising out of or in any way related to your use or application of the content, whether such claim is for breach of contract, tort, negligence or any other cause of action.