Daktronics

Moxa EDS-205A-M-ST (A-2580) Settings and Troubleshooting

Topic

  • Settings are not correct for the Moxa EDS-205A-M-ST switch found in the fiber box, and SportSound 500 control enclosure and 1500 cabinets.

Environment

  • Products: Fiber Box, 500HD, 1500HD
  • Components: A-2580 Moxa ADS-205A-M-ST Switch
  • Control Systems: Audio, CobraNet Discovery

Steps

  1. Ensure power is connected to the green terminal block: Red to V1+ and black to V1-.
    A-2580 BSP-Power.png
  2. Ensure BSP DIP switches next to power connection are both set to ON.
  3. Verify fiber cables are connected to RX and TX (circle 3).
    A-2580 Indicators.png
  4. Verify Ethernet cable connection(s) from other equipment (circle 3).  Typical connections for Daktronics standard systems:
    1. Fiber Conversion Box: ADC1 (Audia EXPI/O-2, Whirlwind CI2L EMOD, Diagnostic Port)
    2. Control Enclosure: Amplifiers (number varies by audio system)
  5. Verify Network Activity:
    1. P1 LED should be illuminated amber to indicate switch has power (circle 1).
      • If P1 LED is not illuminated:
        • Verify proper connections to power supply (Red to V1+, Black to V1-).
        • Verify power supply is supplying 24VDC.
        • Try connecting power to V2 inputs (Red to V2+, Black to V2-), and verify P2 illuminates (circle 1).
    2. Port 1 (100M) LED will illuminate solid green to indicate a functional connection between the fiber box and control enclosure (or switch to switch) (circle 2).
      • If this LED is not illuminated:
        • Switch fiber parts at the fiber conversion box.
        • Test fiber cable, and terminate as necessary.
        • Bypass fiber jumpers.
        • Verify power and connectivity at other end of the switch.
        • If still not illuminating, replace switch.
    3. Each Ethernet jack also has an LED that will illuminate when a cable to other equipment is connected (circle 2).
      • If these LEDs are not illuminating:
        • Check Ethernet cable/connections.
        • Verify connection on opposite end of Cat5e cable.
        • Connect known working cable and equipment (laptop).
        • If still not illuminating, replace switch.

KB ID: DD3802861

DISCLAIMER: Use of this content may void the equipment warranty, please read the disclaimer prior to performing any service of the equipment.

DAKTRONICS DOES NOT PROMISE THAT THE CONTENT PROVIDED HEREIN IS ERROR-FREE OR THAT ANY DEFECTS WILL BE CORRECTED, OR THAT YOUR USE OF THE CONTENT WILL PROVIDE SPECIFIC RESULTS. THE CONTENT IS DELIVERED ON AN "AS-IS" AND "AS-AVAILABLE" BASIS. ALL INFORMATION PROVIDED IN THIS ARTICLE IS SUBJECT TO CHANGE WITHOUT NOTICE. DAKTRONICS DISCLAIMS ALL WARRANTIES, EXPRESS OR IMPLIED, INCLUDING ANY WARRANTIES OF ACCURACY, NON-INFRINGEMENT, MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE. DAKTRONICS DISCLAIMS ANY AND ALL LIABILITY FOR THE ACTS, OMISSIONS AND CONDUCT OF YOU OR ANY THIRD PARTIES IN CONNECTION WITH OR RELATED TO YOUR USE OF THE CONTENT. ADJUSTMENT, REPAIR, OR SERVICE OF THE EQUIPMENT BY ANYONE OTHER THAN DAKTRONICS OR ITS AUTHORIZED REPAIR AGENTS MAY VOID THE EQUIPMENT WARRANTY. YOU ASSUME TOTAL RESPONSIBILITY FOR YOUR USE OF THE CONTENT AND ANY LINKED CONTENT. YOUR SOLE REMEDY AGAINST DAKTRONICS FOR DISSATISFACTION WITH THE CONTENT IS TO STOP USING THE CONTENT. THIS LIMITATION OF RELIEF IS A PART OF THE BARGAIN BETWEEN THE PARTIES.

The above disclaimer applies to any property damage, equipment failure, liability, infringement, or personal injury claim arising out of or in any way related to your use or application of the content, whether such claim is for breach of contract, tort, negligence or any other cause of action.